?

Log in

No account? Create an account

Previous | Next

How loquacious of you!

This is the most verbose boot time output from a network device I've ever seen. It's practically Linux-like in the stream-of-consciousness narrative of "how I came to be able to switch packets."

Wait for rebooting..........................................

Loading Diagnostic Image File : EIF8X10G-dv3100.bin 

Diagnostics 3.1.0.0
Normal Mode

--- Performing Power-On Self Tests (POST) ---
DUMMY Test 1 ................. PASS
UART Loopback Test ........... PASS
DRAM Test .................... PASS
Timer Test ................... PASS
PCI Device 1 Test ............ PASS
I2C Bus Initialization ....... PASS
Switch Int Loopback Test ..... PASS
Done All Pass.
------------------ DONE ---------------------


Loading Runtime Image File : EIF8X10G-v22623.bin
Runtime 2.2.6.23

Press Ctrl+[ to enable stkctrl debug message
PCI unit 0: Dev 0x5670, Rev 0x02, Chip BCM5670_A1, Driver BCM5670_A0
PCI unit 1: Dev 0x5673, Rev 0x02, Chip BCM5673_A1, Driver BCM5673_A0
PCI unit 2: Dev 0x5673, Rev 0x02, Chip BCM5673_A1, Driver BCM5673_A0
PCI unit 3: Dev 0x5673, Rev 0x02, Chip BCM5673_A1, Driver BCM5673_A0
PCI unit 4: Dev 0x5673, Rev 0x02, Chip BCM5673_A1, Driver BCM5673_A0
PCI unit 5: Dev 0x5673, Rev 0x02, Chip BCM5673_A1, Driver BCM5673_A0
PCI unit 6: Dev 0x5673, Rev 0x02, Chip BCM5673_A1, Driver BCM5673_A0
PCI unit 7: Dev 0x5673, Rev 0x02, Chip BCM5673_A1, Driver BCM5673_A0
PCI unit 8: Dev 0x5673, Rev 0x02, Chip BCM5673_A1, Driver BCM5673_A0
PCI device BCM5670_A1 attached as unit 0.
PCI device BCM5673_A1 attached as unit 1.
PCI device BCM5673_A1 attached as unit 2.
PCI device BCM5673_A1 attached as unit 3.
PCI device BCM5673_A1 attached as unit 4.
PCI device BCM5673_A1 attached as unit 5.
PCI device BCM5673_A1 attached as unit 6.
PCI device BCM5673_A1 attached as unit 7.
PCI device BCM5673_A1 attached as unit 8.
AN983 found.  
Fan controller detected.
Thermal 0 sensor detect.
DNS_ResolverInit..OK
DNS_Proxy_init ....OK

Set Transition mode ...
[get stackingMac done ret_val] = 1
Assigned Unit ID:[1]
stacking DB: unit = 0, module type = 0

Finish Set Transition mode ...
Enter Transition mode ...
Finish Transition mode ...
Enter Master mode ...
ISC: Stack status: Normal
swdrv Master - 
 ...stack id - 1
 ...base port ID - 1
 ...port_number - 9
 ...units - 1
 ...unit_tbl[0] - 1
 ...stacking port - 0

Load certificate files : Starting
Load certificate files : Finished

Finish Master mode ...

Performing startup provision ...
CLI enter main (PROVISION)
Press [P] to print out the d                                                    
........................................................................
........................................................................
.....................................................................
Notify provision complete


Provision Complete ...
Finish Provision Complete ...
[get stackingMac done ret_val] = 1
XFER: End of config sync.

Username:

Tags:

Profile

14L
szasz
Charley

Latest Month

July 2013
S M T W T F S
 123456
78910111213
14151617181920
21222324252627
28293031